| Splice
& Seal ™
The Forced Encapsulated System has proven itself
over many years of success in major Telco’s.
Splice & Seal™ was designed to reduce
overall cost and incorporate labor saving methods
and materials. It can be used on Filled or Air
Core Pic Cable, either Direct Buried, Aerial or
Underground in various splice configurations. |
|
|
 |
KIT
A (TPIKRU-A)
SIZE A: 25-200 PAIR, 22-26 AWG
FORCED ENCAPSULATED SPLICE KIT
Specifications:
Splice Opening: 12”
Module Bank: Single
Splice Configuration: Inline/FoldBack
Splice Bundle Diameter: 3.0+/-
Encapsulant: 750 gm +/-
Click for Kit Contents:
|
 |
KIT
B (TPIKRU-B)
SIZE B: 300-400 PAIR, 22-26 AWG
FORCED ENCAPSULATED SPLICE KIT
Specifications:
Splice Opening: 20”
Module Bank: 2 Bank
Splice Configuration: Inline/FoldBack
Splice Bundle Diameter: 4.25+/-
Encapsulant: 1500 gm +/-
Click for Kit Contents:
|
 |
KIT
C (TPIKRU-C)
SIZE C: 600 PAIR, 22-26 AWG
FORCED ENCAPSULATED SPLICE KIT
Specifications:
Splice Opening: 20”
Module Bank: 2 Bank
Splice Configuration: Inline
Splice Bundle Diameter: 5.25+/-
Encapsulant: 1900 gm +/-
Click for Kit Contents:
|
Click
here for Kit Comparison:
Forced Encapsulated Installation Practices (.pdf)
|
Splice & Seal ™ Forced Encapsulated Splice Kit
Sufficient Material to Complete Multiple Splice
and Sheath Repairs.
Cable Splice and Sheath Repair Closure System
This system was designed to reduce overall cost
and to be used on
Filled or Air Core PIC cable, either Direct Buried,
Aerial or Underground, Pulp/Paper Insulated Cable.
This has been an
environmentally and mechanically proven closure
tested and installed by major telecoms for over
two decades.
Splice Encapsulation/Sheath Repair Kit (TPI60--SEK)
Splice Encapsulation/Sheath
Repair Kit (TPI61-SEK)
Splice Encapsulation/Sheath
Repair Kit (TPI62-SEK)
|
Sheath Repair Practices (.pdf) |
Splice
& Seal ™ Non Pressurized
& Filled Cable
Sheath Repair Kit (TPISR-KIT)
For repair of PIC Filled or Air Core cables not
under air pressure.
One kit will complete approximately 9
repairs on 2.25” diameter cable and 14 repairs
on 1.0” diameter cable.
Click for Kit Contents:
|
Sheath Repair Practices (.pdf) |
Splice
& Seal ™ Pressurized
Sheath Repair Kit (TPIPR-KIT)
For repairs of damaged sheath up to 16”
in length and cable size up to 3600 pair.
Note: For repairs of damaged sheath in
excess of 16” additional kit(s) required.
Click for Kit Contents:
|
 |
Splice
& Seal ™ Strain Relief
Kit (TPI69-SRK)
Replacement components to be used with TPI62-SEK
Splice Encapsulation/Sheath Repair Kit
Click for Kit Contents:
|
 |
Splice
& Seal ™ Pedestal Splice
Sealing Kit
3” Splice Diameter x 17” (TPI-PSSK-A)
6” Splice Diameter x 17” (TPI-PSSK-B)
The Splice & Seal™ Pedestal Splice Sealing
Kit is provided to economically seal the Terminal
Block Splice or Service Wire/Ground Wire Splice
from water, water vapor, U.V., insects or rodent
intrusion. Splice can be sealed or totally Encapsulated.
Click for Kit Contents: |
